Heunis Steel manufactures a wide range of rainwater goods such as gutters, downpipes, offsets, gutter angles & other accessories. The appropriate zinc coating on our rainwater goods are one of the many characteristics that make our products such high quality. Our gutters, downpipes and other rainwater goods are ideal for rainwater harvesting which can be used anywhere and is easy to install.
Manufactured from SABS-quality galvanised steel varying in thickness depending on individual needs and architects specifications.
Three different Shapes of brackets are manufactured - standard purlin brackets, standard facia brackets and swivel facia brackets.
Stopends are used to close the open end of the gutter to ensure that the water drains through the outlet and not the open end of the gutter. It is universal and easy to install.
A lip around the stopend allows for a 3.5mm hole to be drilled on both vertical sides and can be fastened to the gutter using a 3.2mm waterproof rivet.
Protective Coating after Installation
A good quality acrylic PVA paint should be used to paint the galvanised material which will ensure a durable stylish installation that will last many years.
Manufactured from SABS-quality galvanised steel of varying thickness depending on individual needs and architects specifications.
Two Shapes of Gutter Angles are manufactured, namely Internal and External.
The main purpose of an angle is to enable the installer to do do an installation where it is required that the gutter must continue around a corner of the roof.
The Gutter Angle is approximately 300mm long on either side to ensure a durable joint with the rest of the gutter.
Always ensure that the joint is sealed with a good quality butal rubber sealant - normal silicone is not recommended for this application.
Protective Coating After Installation
A good quality acrylic PVA paint should be used to paint the galvanised material which will ensure a durable stylish installation that will last many years.
Manufactured from 0.5mm Z275 SABS-quality material to meet SABS 1848 specifications.
We are proud to be South Africa’s largest manufacturer of SABS-approved galvanised geyser trays.
Our patented design distinguishes us from all other manufacturers and enables us to provide a quality product that will last many years.
Geyser trays are installed under the geyser to collect any leaks from the geyser and valves. This leaked water is discharged through a 50mm hole on the short side of the tray into a 50mm discharge pipe through the roof and out the building.
According to the SABS 0524 specification it is now LAW to have a geyser tray installed withevery geyser installation inside a roof.
Protective Coating after Installation
No protective coating required after installation.
Manufactured from SABS-certified raw material, the grease trap strainer is a very effective method of preventing drain blockage by collecting all unwanted objects and preventing them from entering
your waste and drainpipes.
Grease trap strainers are installed in the gully of a drain and have a specific design to allow easy access and regular cleaning.
Protective Coating after Installation
A good quality acrylic PVA paint should be used to paint the galvanised material which will ensure a durable stylish installation that will last many years
Manufactured from SABS-quality 0.5mm and 0.6mm (Z275) galvanised material at a standard 30 degree pitch.
The purpose of a vent flashing is to effectively seal the roof where vent pipes exit through the roof.
All our vent flashings are mounted on a 450 x 450mm square base to ensure enough cover for an effective and durable installation.
Protective Coating after Installation
A good quality acrylic PVA paint should be used to paint the galvanised material which will ensure a durable stylish installation that will last many years.
Stovepipes are manufactured in standard 900mm lengths to fit coal stoves of various sizes traditionally used in urban and rural areas.
The purpose of a stovepipe is to effectively channel the smoke from the stove through the roof and out the building.
The above product is manufactured from SABS-certified raw material
Protective Coating after Installation
A good quality acrylic PVA paint should be used to paint the galvanised material which will ensure a durable stylish installation that will last many years
Manufactured from SABS-quality galvanised steel varying in thickness depending on individual needs and architects specifications.
Waterheads are mainly used on bigger buildings where large volumes of water are displaced into a downpipe that channels down the building.
Occasionally the architectural design does not allow for a plain downpipe to be fitted flush to the outer wall, a waterhead is then required to gather the water and channel it into the next downipe.
Protective Coating after Installation
A good quality acrylic PVA paint should be used to paint the galvanised material which will ensure a durable stylish installation that will last many years
/__upload/Heunis/Catalogue/images/75mm x 2.7m Round Downpipe with Crimped Shoe.jpg&MaxImageWidth=450&MaxImageHeigth=450 "Zoom into the product image")